My account

Eton POW 16+ speakers

Ø 165 mm, 70/100 W, 3 Ω, 94.3 dB (2.83V/1m), installation depth 65 mm
More about the product
We will help you with your purchase
Eton POW 16+ speakers

Eton POW 16+ speakers

165 mm (6.5") 2-way component system with 28 mm fabric tweeter in compact installation dimensions. Double-layer fiberglass reinforced paper diaphragm with strong ferrite magnet. Reinforced, powder-coated metal cage with ventilation and quality connection terminals. with pan and swivel function, including tweeter cable crossover, impedance 3 ohms, rated/music power 70W RMS/100W, efficiency 94.3dB at 2.83V.

The new POW+ series impresses with its new CXS28+ tweeter: a 28mm tweeter with the intelligent installation dimensions of a 25mm tweeter, that means more performance in the lower treble range with the same installation dimensions! Thanks to a large 28mm voice coil combined with an extremely compact coupling volume, an increase in low-end performance was achieved, meaning deeper separation is possible. The new design now has a resonance frequency of 1300 Hz, a full 500 Hz lower than the previous model! The result is deep separation in active operation (as low as 2.4 kHz/12 dB), so the bass/mid-bass driver blends even more easily with the tweeter unit. For all those who need passive tuning - a tweeter cable crossover consisting of a high-quality film capacitor is part of the set. Production and development Made in Germany!

Key features of Eton POW 16+ speakers

  • High sensitivity of 94.3 dB.
  • 28 mm silk tweeter.
  • Ideal for driving only from the car radio.
  • Made in Germany.
Catalog numberPOW 16 PLUS
BrandEton
LinksOfficial web presentation
Speaker typeCoaxial speakers:
Coaxial speakers are characterized by a so-called all-in-one design. The tweeter and mid-bass speaker are in one basket. The advantage is simpler assembly, but thanks to the connection or proximity of the bands in one speaker, the sound quality will usually be reduced. As a rule, in the middle of the mid-bass speaker, there is a tweeter whose voice coil works in the second air gap of the common magnetic circuit. The three-way coaxial speaker consists of a mid-bass speaker, a center speaker and a separate tweeter in the front on a special beam.

Component Speakers:
Component speakers are characterized by a division into individual frequency bands, treble + mid-bass + or. bass band. The individual speakers can be placed completely separately, which results in a better sound and acoustic performance. In the vast majority of cases of component speakers, an external crossover is also supplied, which divides the treble, middle / mid-bass, and into the three-band the bass band or allows setting the decibel level of the tweeter (e.g. +2 dB, 0 dB, -2 dB), steepness (e.g. 6dB/Oct. 12dB/Oct.) or active or bi-amp connection.
Component 2-band
RMS powerRMS speaker power is the constant power of the entire system, not just one speaker or one side. This is also the performance of continuous use of the speakers. If the RMS power is exceeded for a long time, the speakers may be irreversibly damaged! 70 W
Max. (maximum performancePeak performance , which the speaker can play for a moment (approx. 0.5 s), for example when hitting drums in a song. If the max power is exceeded, the speakers will usually be damaged! 100W
Sensitivity (SPL 2.83V/1m)Sensitivity, sensitivity or efficiency of the speaker.

Speaker sensitivity is given in decibels (dB) and simply put, the higher the value, the lower the demands on the amplifier's power. This is a defacto rating of how a speaker converts watts to sound. Sensitivity ratings are in noise level measured at 1 meter from the speaker using 1 W (watt of power) or using 2.83 volts at the source at 1 meter.

A higher decibel level means the speaker is louder with less power. For every 3 dB increase in sensitivity, the speaker requires half the power to reproduce the same volume. For example, if an 88 dB speaker needs 100 Watts to produce a certain volume, then a speaker with a sensitivity of 91 dB needs only 50 Watts to reach the same volume.
94.3dB
ImpedanceImpedance - measurement of electrical resistance. When buying speakers, it is important to make sure that the impedance matches the amplifier or car stereo you are using.

Example:
A 2 Ohm speaker cannot be connected to an amplifier that is only stable up to 4 Ohms! A 4 Ohm speaker can easily be used with an amplifier that is stable up to 2 Ohms. The most common speaker impedance today is 3 - 4 Ohm.
3 Ω
The diameter of the mid-bass speakerWe state the diameter of the speaker as the diameter of the entire speaker, not including the mounts, when smaller speakers (87, 100, 130 mm) have extra mounts. Some speakers are oval and there the dimension is given in inches, always the shortest side to the longest side. One inch is approx. 2.5 cm. 165 mm
Installation depth of the mid-bass speakerThe installation depth of the speaker is measured from the bottom edge of the magnet to the bottom edge of the tin, plastic or cast speaker basket, or speaker bearing surfaces. 65 mm
Tweeter dome diameterThe net diameter of the dome (diaphragm) of the tweeter. 28 mm
Tweeter dome materialThe shell material that was used in the manufacture of the tweeter. Silk
Frequency crossover included in the packageThe crossover is an important part of defacto all loudspeakers. A crossover usually contains different resistor values, coil sizes, and capacitor types that fundamentally modify the sound. We describe below what the turnouts are for.

Component Speakers:
A crossover is part of every quality component speaker system. Its task is to ensure the distribution of frequencies that the amplifier produces in the entire acoustic spectrum of frequencies so that each of the speakers receives only that part of the band that it can optimally play in terms of efficiency and minimal distortion.

Coaxial speakers:
In most cases, coaxial loudspeakers have a simple crossover (6dB/Oct.) formed by a capacitor at the tweeter.
Yes
Cover grids included in the packageOriginal cover grilles in speaker packaging. No
Price forIf the price is for a pair, the package always includes 2 pieces of everything, e.g. 2x mid-bass, 2x tweeter and 2x crossover. Few

Product comments

Evaluation

Overall rating
0 %
No one has rated the product yet
Rate the product:
ask us
We will only use your data to send you a reply.