Speakers for BMW Morel IR-BMW42INT

Speakers for BMW Morel IR-BMW42INT

Morel presents a unique OEM system for BMW cars with the sole aim of offering top quality sound without compromise in the spirit of plug & play. Two sets of speaker systems available that simply have no equivalent in sound quality on the market today. As part of the Reference Series, the Morel IR-BMW42INT 2-way coaxial system takes acoustic performance in BMW cars to a whole new level. Music lovers will be overwhelmed by the level of tonal clarity and detail they are used to from Morel speakers. Featuring DirectFit, a unique 4” chassis design with included mounting brackets, easy snap-in 1.1” (28mm) tweeters and factory cable connections, the IR-BMW42INT allows for installation in all BMW models without any modifications.

Technical parameters of Morel IR-BMW42INT speakers

The IR-BMW42 coaxial system is based on Morel's globally acclaimed Hybrid series. The 4-inch (100mm) mid-woofer uses a 2.1” (54mm) voice coil, which is up to 3x larger than conventional speakers. The EVC™ design moves the magnetic drive system inside the voice coil and eliminates magnetic flux by effectively directing all magnetic energy into the voice coil. The result is an ultra efficient and powerful system with efficient heat dissipation and reduced distortion. The high-resolution tweeter uses Morel's 28mm Acuflex™ silk dome and a dual neodymium magnet motor that is up to four times more powerful than conventional designs of the same size. With a hybrid system, more of the amplified power is converted into sound energy for flawless performance, even in a small driver. These technologies are underlined by the ultra-light DPC (Damped Polymer Cone) membrane, which stands out with exceptional sound quality without coloration and exemplary self-damping. All this will enable a plug-and-play speaker system that is simply unmatched. Due to the high quality of this system, the installation of an appropriate amplifier and DSP processor is required.

Main features of Morel IR-BMW42INT speakers

• Top quality coaxial speakers for BMW cars.
• Easy installation in all BMW models thanks to the DirectFit design.
• The same size, shape and connectors as the factory speakers.
• Optimized sound performance for BMW cars based on the acclaimed Hybrid series.
• High performance, minimal distortion and top sound typical of Morel.
• High resolution tweeter with 28mm Acuflex™ silk dome.
• 2.1” (54mm) voice coil and powerful EVC™ hybrid motor.
• Ultralight paper composite mid-bass membrane for faithful sound.
• Plug & play wiring for quick and easy installation.
• Designed for matching amplifier and DSP processor.
• Mounting material included in the package for all BMW models.

Catalog number	IR-BMW42INT
Brand	Morel
Links	Official web presentation (English)
Speaker typeCoaxial speakers: Coaxial speakers are characterized by a so-called all-in-one design. The tweeter and mid-bass speaker are in one basket. The advantage is simpler assembly, but thanks to the connection or proximity of the bands in one speaker, the sound quality will usually be reduced. As a rule, in the middle of the mid-bass speaker, there is a tweeter whose voice coil works in the second air gap of the common magnetic circuit. The three-way coaxial speaker consists of a mid-bass speaker, a center speaker and a separate tweeter in the front on a special beam. Component Speakers: Component speakers are characterized by a division into individual frequency bands, treble + mid-bass + or. bass band. The individual speakers can be placed completely separately, which results in a better sound and acoustic performance. In the vast majority of cases of component speakers, an external crossover is also supplied, which divides the treble, middle / mid-bass, and into the three-band the bass band or allows setting the decibel level of the tweeter (e.g. +2 dB, 0 dB, -2 dB), steepness (e.g. 6dB/Oct. 12dB/Oct.) or active or bi-amp connection.	Component 2-band
RMS powerRMS speaker power is the constant power of the entire system, not just one speaker or one side. This is also the performance of continuous use of the speakers. If the RMS power is exceeded for a long time, the speakers may be irreversibly damaged!	80 W
Max. (maximum performancePeak performance , which the speaker can play for a moment (approx. 0.5 s), for example when hitting drums in a song. If the max power is exceeded, the speakers will usually be damaged!	250 W
Sensitivity (SPL 2.83V/1m)Sensitivity, sensitivity or efficiency of the speaker. Speaker sensitivity is given in decibels (dB) and simply put, the higher the value, the lower the demands on the amplifier's power. This is a defacto rating of how a speaker converts watts to sound. Sensitivity ratings are in noise level measured at 1 meter from the speaker using 1 W (watt of power) or using 2.83 volts at the source at 1 meter. A higher decibel level means the speaker is louder with less power. For every 3 dB increase in sensitivity, the speaker requires half the power to reproduce the same volume. For example, if an 88 dB speaker needs 100 Watts to produce a certain volume, then a speaker with a sensitivity of 91 dB needs only 50 Watts to reach the same volume.	90dB
ImpedanceImpedance - measurement of electrical resistance. When buying speakers, it is important to make sure that the impedance matches the amplifier or car stereo you are using. Example: A 2 Ohm speaker cannot be connected to an amplifier that is only stable up to 4 Ohms! A 4 Ohm speaker can easily be used with an amplifier that is stable up to 2 Ohms. The most common speaker impedance today is 3 - 4 Ohm.	4 Ω
Frequency rangeThe ability of the speakers to play a signal from the lowest frequency to the highest, or the speaker's ability to faithfully reproduce sound in a specific frequency band. Professionally: In the frequency range from 40 to 16,000 Hz, the vast majority of fundamental and overtones (harmonics) of all musical instruments are found. We are interested in the course of the radiated sound pressure in this range of frequencies when the loudspeaker system is supplied with constant power. We call this course the frequency characteristic, which tells us the level of radiated sound pressure in decibels (dB) depending on the frequency. The frequency characteristic of a speaker or speaker system can be expressed most succinctly with a graph. Mostly, however, the frequency characteristic is indicated by indicating the maximum tolerance of the sound pressure in the given frequency range, e.g. 50 to 15,000 Hz -+ 6 dB. Since the frequency characteristics of loudspeakers and systems in general are quite uneven, some manufacturers do not even specify this maximum tolerance of sound pressure in decibels in their catalogs for reasons of prestige. Data impoverished in this way is unfortunately worthless. What is valid is that the manufacturer offers a speaker system with a frequency range of 30 to 20,000 Hz, if he is worried about stating the maximum unevenness of the sound pressure in this range, because he can have a tolerance of, for example, +- 20 dB. The unevenness or undulation of the frequency curve in good speaker systems for high-quality music performance should not exceed +-3 dB in the 80 to 12,000 Hz band and +-6 dB in the 40 to 16,000 Hz band. Greater unevenness already depletes or emphasizes certain tonal areas, which can cause audible or even disturbing distortion. The proportion between fundamental tones and higher harmonics also changes, thereby changing the color of the sound, and individual musical instruments as well as the entire musical image sound unnatural.	80 - 25,000 Hz
The diameter of the mid-bass speakerWe state the diameter of the speaker as the diameter of the entire speaker, not including the mounts, when smaller speakers (87, 100, 130 mm) have extra mounts. Some speakers are oval and there the dimension is given in inches, always the shortest side to the longest side. One inch is approx. 2.5 cm.	100 mm
Mid-woofer diaphragm materialThe material that was used for the speaker diaphragm. Don't be afraid of the paper, it surprisingly has a very natural and high-quality sound and, thanks to the surface treatment, it can withstand moisture without any problems.	DPC (Dumped Polymer Cone)
Tweeter dome diameterThe net diameter of the dome (diaphragm) of the tweeter.	28 mm
Tweeter dome materialThe shell material that was used in the manufacture of the tweeter.	Acuflex™ (combination of silk and paper)
Frequency crossover included in the packageThe crossover is an important part of defacto all loudspeakers. A crossover usually contains different resistor values, coil sizes, and capacitor types that fundamentally modify the sound. We describe below what the turnouts are for. Component Speakers: A crossover is part of every quality component speaker system. Its task is to ensure the distribution of frequencies that the amplifier produces in the entire acoustic spectrum of frequencies so that each of the speakers receives only that part of the band that it can optimally play in terms of efficiency and minimal distortion. Coaxial speakers: In most cases, coaxial loudspeakers have a simple crossover (6dB/Oct.) formed by a capacitor at the tweeter.	Yes
Cover grids included in the packageOriginal cover grilles in speaker packaging.	No
Price forIf the price is for a pair, the package always includes 2 pieces of everything, e.g. 2x mid-bass, 2x tweeter and 2x crossover.	Few